- News
- All
- Aerospace & Defence
- Antenna
- Applications
- Automotive
- Capacitors
- Circuit Protection Devices
- electro-mechanical news
- Filters
- Fuses
- Inductors
- Industrial
- Integrated Passives
- inter-connect news
- Market & Supply Chain
- Market Insights
- Medical
- Modelling and Simulation
- New Materials & Supply
- New Technologies
- Non-linear Passives
- Optoelectronics and Isolation
- Oscillators
- Passive Sensors News
- Resistors
- RF & Microwave
- Telecommunication
- Weekly Digest
- News
- All
- Aerospace & Defence
- Antenna
- Applications
- Automotive
- Capacitors
- Circuit Protection Devices
- electro-mechanical news
- Filters
- Fuses
- Inductors
- Industrial
- Integrated Passives
- inter-connect news
- Market & Supply Chain
- Market Insights
- Medical
- Modelling and Simulation
- New Materials & Supply
- New Technologies
- Non-linear Passives
- Optoelectronics and Isolation
- Oscillators
- Passive Sensors News
- Resistors
- RF & Microwave
- Telecommunication
- Weekly Digest
Applications e-Blog
Standard vs Planar LLC transformers Comparison for Battery Chargers
The webinar by Frenetic examines two LLC transformers designed for a 300 W half‑bridge LLC stage with approximately 400 V...
Read moreDetailsGalvanic Isolation: Methods, Standards and Design
Galvanic isolation separates circuits without a direct conductive connection while allowing signals or power to cross an insulating barrier. For...
Read moreDetails2026 Power Magnetics Design Trends: Flyback, DAB and Planar
Power electronics teams entering 2026 face tighter space, efficiency and time‑to‑market constraints, while magnetics must still behave predictably across thermal...
Read moreDetailsEnabling Software‑Defined Vehicle Architectures: Automotive Ethernet and Zonal Smart Power
This article, based on the Würth Elektronik and onsemi webinar “Simplifying Vehicle Development with Automotive Ethernet and Zonal Smart Switch...
Read moreDetailsPower Electronics Tools for Passives and Magnetic Designs
Modern power electronics design relies on a diverse toolbox, from general‑purpose circuit simulators to highly specialized magnetics and component‑selection platforms....
Read moreDetailsDC/DC Push‑Pull Converter vs PSFB Design Guide
Push‑pull converters remain attractive in isolated DC/DC stages where cost and simplicity are key, but their practical design window is...
Read moreDetailsTransient Suppression Guide
This presentation from Würth Elektronik provides brief overview of transient suppression guide for beginners. As the number of electronic devices connected to...
Read moreDetailsOvervoltage and Transient Protection for DC/DC Power Modules
This presentation from Würth Elektronik by Timur Uludag delves into overvoltage protection for safe operation-transient protection for non-isolated DC/DC Power Modules in...
Read moreDetails3-Phase EMI Filter Design, Simulation, Calculation and Test
3-phase EMI filters reduce conducted common-mode and differential-mode interference when their components, topology and installation are designed around the actual...
Read moreDetailsCommon Mode Chokes Selection for RF Circuits in Next-Generation Communication Systems
This presentation from Würth Elektronik by Ashiro Chen and Iván Arias provides characterization and selection of common mode choke parameters for DC...
Read moreDetailsPopular Posts
-
Buck Converter Design and Calculation
-
September 2026 Interconnect, Passives and Electromechanical Components Market Insights
-
Boost Converter Design and Calculation
-
Capacitor Charging and Discharging
-
LLC Resonant Converter Design and Calculation
-
RF Connector Types: How To Choose the Right One
-
Flyback Converter Design and Calculation
-
Passive Low Pass Filters: Fundamentals and EMI Design
-
Audio Capacitors: Choosing Capacitors for Crossover Circuits
-
MLCC and Ceramic Capacitors
© 2015–2026
All rights reserved