Passive Components Blog
No Result
View All Result
  • Home
  • News
    • All
    • Aerospace & Defence
    • Antenna
    • Applications
    • Automotive
    • Capacitors
    • Circuit Protection Devices
    • electro-mechanical news
    • Filters
    • Fuses
    • Inductors
    • Industrial
    • Integrated Passives
    • inter-connect news
    • Market & Supply Chain
    • Market Insights
    • Medical
    • Modelling and Simulation
    • New Materials & Supply
    • New Technologies
    • Non-linear Passives
    • Optoelectronics and Isolation
    • Oscillators
    • Passive Sensors News
    • Resistors
    • RF & Microwave
    • Telecommunication
    • Weekly Digest
    Miba Resistors SC-55 surface-mount thick-film power resistor with its body and connection pads visible

    Miba Unveils 55 W SMD Thick-Film Power Resistor in TO-263

    CapXon PM and EV surface-mount capacitors with cylindrical cans and rectangular mounting bases

    CapXon Extends Polymer and SMD Aluminum Capacitors

    YAGEO Group KEMET VW80808 automotive MLCC illustration with rectangular ceramic bodies and metal end terminations

    YAGEO Expands VW80808 Automotive MLCCs with X8R, X8G and C0G

    Kyocera SD25 duplexers and SF25/SF20 SAW filters in surface-mount packages, shown in top and underside views.

    Kyocera Expanded SAW Filters and Duplexers for Base Stations

    IQD IQXT-601 and IQXT-602 surface-mount TCXOs in rectangular ceramic packages

    IQD Releases TCXOs for GNSS and RF Timing

    Vishay VJ series surface-mount ceramic safety capacitors with rectangular bodies and metal end terminations

    Vishay Introduces X1 Safety MLCCs for AC Line Filtering

    Illustrative aerospace electronics assembly with board-to-board connectors, coaxial RF cables and optical links.

    Military and Aerospace Interconnect Design: Key Trade-offs

    Samsung Introduces 630V X7T Molded Frame Capacitor for Automotive

    Exxelia Presents Disc Capacitors and Integrated Magnetics for Space

    Trending Tags

    • Ripple Current
    • RF
    • Leakage Current
    • Tantalum vs Ceramic
    • Snubber
    • Low ESR
    • Feedthrough
    • Derating
    • Dielectric Constant
    • New Products
    • Market Reports
  • Knowledge Blog
  • Dossiers
    • Aerospace and Defense Passive Components Dossier
    • AI Hardware Dossier
    • Automotive Dossier
    • Industrial Robotics Dossier
    • Power Converter Dossier
    • Capacitor Dossier
    • Circuit Protection Dossier
    • Inductor Dossier
    • Resistor Dossier
    • Silicon Capacitors and Integrated Passives Dossier
  • Suppliers
    • Who is Who
  • PCNS
    • PCNS 2025
    • PCNS 2023
    • PCNS 2021
    • PCNS 2019
    • PCNS 2017
  • Events
  • Home
  • News
    • All
    • Aerospace & Defence
    • Antenna
    • Applications
    • Automotive
    • Capacitors
    • Circuit Protection Devices
    • electro-mechanical news
    • Filters
    • Fuses
    • Inductors
    • Industrial
    • Integrated Passives
    • inter-connect news
    • Market & Supply Chain
    • Market Insights
    • Medical
    • Modelling and Simulation
    • New Materials & Supply
    • New Technologies
    • Non-linear Passives
    • Optoelectronics and Isolation
    • Oscillators
    • Passive Sensors News
    • Resistors
    • RF & Microwave
    • Telecommunication
    • Weekly Digest
    Miba Resistors SC-55 surface-mount thick-film power resistor with its body and connection pads visible

    Miba Unveils 55 W SMD Thick-Film Power Resistor in TO-263

    CapXon PM and EV surface-mount capacitors with cylindrical cans and rectangular mounting bases

    CapXon Extends Polymer and SMD Aluminum Capacitors

    YAGEO Group KEMET VW80808 automotive MLCC illustration with rectangular ceramic bodies and metal end terminations

    YAGEO Expands VW80808 Automotive MLCCs with X8R, X8G and C0G

    Kyocera SD25 duplexers and SF25/SF20 SAW filters in surface-mount packages, shown in top and underside views.

    Kyocera Expanded SAW Filters and Duplexers for Base Stations

    IQD IQXT-601 and IQXT-602 surface-mount TCXOs in rectangular ceramic packages

    IQD Releases TCXOs for GNSS and RF Timing

    Vishay VJ series surface-mount ceramic safety capacitors with rectangular bodies and metal end terminations

    Vishay Introduces X1 Safety MLCCs for AC Line Filtering

    Illustrative aerospace electronics assembly with board-to-board connectors, coaxial RF cables and optical links.

    Military and Aerospace Interconnect Design: Key Trade-offs

    Samsung Introduces 630V X7T Molded Frame Capacitor for Automotive

    Exxelia Presents Disc Capacitors and Integrated Magnetics for Space

    Trending Tags

    • Ripple Current
    • RF
    • Leakage Current
    • Tantalum vs Ceramic
    • Snubber
    • Low ESR
    • Feedthrough
    • Derating
    • Dielectric Constant
    • New Products
    • Market Reports
  • Knowledge Blog
  • Dossiers
    • Aerospace and Defense Passive Components Dossier
    • AI Hardware Dossier
    • Automotive Dossier
    • Industrial Robotics Dossier
    • Power Converter Dossier
    • Capacitor Dossier
    • Circuit Protection Dossier
    • Inductor Dossier
    • Resistor Dossier
    • Silicon Capacitors and Integrated Passives Dossier
  • Suppliers
    • Who is Who
  • PCNS
    • PCNS 2025
    • PCNS 2023
    • PCNS 2021
    • PCNS 2019
    • PCNS 2017
  • Events
No Result
View All Result
Passive Components Blog
No Result
View All Result

Littelfuse Presents Ultra-Miniature Half-Pitch SMT DIP Switches

7.4.2026
Reading Time: 7 mins read
A A

Littelfuse introduces TDB series ultra‑miniature, half‑pitch surface‑mount DIP switches that are designed for high‑density PCB layouts where space, reliability, and where automated assembly is critical.

They provide gold‑plated, washable contacts in a 1.27 mm pitch format, giving design engineers a compact way to implement configuration and address settings in low‑power control systems.

RelatedPosts

Littelfuse Introduces TVS Diodes for HVDC Protection

Littelfuse C&K SDE End-Stackable SMT DIP Switches

Littelfuse Introduces Extremely Low Clamping Voltage TVS Diodes for Automotive Protection

Key features and benefits

The Littelfuse TDB Series targets designers who need traditional DIP functionality in layouts that are significantly smaller than legacy through‑hole or full‑pitch SMT switches.

  • Ultra‑miniature 1.27 mm half‑pitch footprint enables higher component density on crowded PCBs.
  • Surface‑mount construction supports standard SMT assembly flows and automated pick‑and‑place.
  • Gold‑plated bifurcated contacts provide low, stable contact resistance and improved corrosion resistance.
  • Top‑tape sealed housing allows reflow soldering followed by aqueous cleaning without contaminating the internal mechanism.
  • Contact ratings up to 50 V DC, 100 mA (steady state) are suitable for configuration, address and low‑power logic switching, not for power paths.
  • Mechanical and electrical life of 1,000 cycles matches typical use where switches are set infrequently and left in position for long periods.
  • Available in 2, 4, 6, 8, and 10 position variants, so engineers can choose just enough configuration range without wasting board area.
  • Tube and tape‑and‑reel packaging options align with both prototyping and high‑volume production.

For engineers familiar with traditional DIP switches, the main benefit is achieving the same configuration behavior in far less board area, while retaining a fully serviceable, manually actuated interface.

Typical applications

The TDB Series is intended for low‑power, low‑frequency signal paths where a simple on/off or address pattern must be set during production, commissioning, or service.

  • Industrial control equipment (address settings for I/O modules, node IDs, feature enable/disable).
  • Power supplies and inverter systems (configuration pins, protection threshold selection, mode selection on control boards).
  • Security and fire alarm systems (zone addressing, feature configuration, local overrides).
  • Building automation and smoke detection equipment (bus addresses, parameter selection, commissioning settings).
  • Consumer IoT and smart home devices (local configuration when no full UI is present, fallback settings during service).

A common pattern is to use a small TDB device to define address bits for a bus‑connected module, or to select between firmware modes without needing a separate connector, jumper, or programming interface.

Technical highlights

From a component selection standpoint, the TDB Series combines a small mechanical envelope with parameters optimized for signal‑level switching.

  • Pitch and format
    • Half‑pitch 1.27 mm contact spacing.
    • Surface‑mount package optimized for reflow processes.
  • Contact system
    • Gold‑plated bifurcated contacts for higher contact reliability and lower risk of intermittent behavior at small currents.
    • Maximum contact resistance specified in the manufacturer datasheet, suitable for logic‑level circuits.
  • Electrical ratings (according to manufacturer datasheet)
    • Up to 50 V DC, 100 mA steady‑state contact rating.
    • Suitable for low‑power digital and control signals; not intended to switch inductive loads or mains.
  • Mechanical and environmental
    • Mechanical and electrical life of 1,000 actuation cycles, which is adequate for configuration switches that are not meant for frequent user interaction.
    • Washable, top‑tape sealed housing supporting post‑reflow cleaning.

When designing around these switches, treat them as signal‑level configuration elements and ensure that any higher energy paths are handled by dedicated relays or solid‑state devices.

Series variants and dimensions

The series covers several position counts, trading off configuration range against PCB length:

  • TDB02 – 2 positions, very small footprint for minimal configuration needs.
  • TDB04 – 4 positions for basic address or mode selection.
  • TDB06 – 6 positions as a compromise between density and flexibility.
  • TDB08 – 8 positions for extended address or option fields.
  • TDB10 – 10 positions when the maximum number of settings is required in a linear DIP format.

Body lengths follow the position count; exact values should be taken from the manufacturer datasheet and mechanical drawings when laying out the PCB.

Design‑in notes for engineers

When replacing a traditional DIP or jumper header with the TDB Series, a few layout and system‑level considerations help avoid issues in production:

  • PCB layout and clearances
    • Respect the 1.27 mm pitch and manufacturer‑specified land pattern to maintain solder joint reliability.
    • Keep silkscreen markings clear and legible despite the smaller body; consider magnified markings or unique designators near the switch for service personnel.
  • Manufacturing and cleaning
    • The top‑tape seal is designed to tolerate reflow and aqueous cleaning; nonetheless, align your reflow and wash profiles with manufacturer guidance.
    • If using aggressive cleaning chemistries, confirm compatibility with Littelfuse recommendations and perform qualification.
  • Electrical design
    • Use these switches only in low‑current, low‑voltage control circuits as defined in the datasheet.
    • For very low current sensing inputs (microamp range), evaluate whether pull‑ups/pull‑downs and input filtering will tolerate the specified contact resistance and its variation over life.
  • Reliability and usage profile
    • The 1,000‑cycle rating is more than sufficient for production setup and occasional field reconfiguration, but not intended for daily user interaction.
    • For applications where settings might be changed frequently, consider whether a different user interface (rotary encoder, push buttons, software settings) is more appropriate.

By following these guidelines, design engineers can leverage the compact TDB footprint without compromising manufacturability, testability, or long‑term field performance.

Source

This article is based on information provided in the official Littelfuse press release and associated TDB Series product documentation on the manufacturer website, with added independent commentary aimed at design engineers and component buyers.

References

  1. Littelfuse/C&K introduces TDB Series ultra-miniature half-pitch surface-mount DIP switches – official press release
  2. Littelfuse TDB Series product page

Related

Recent Posts

Miba Resistors SC-55 surface-mount thick-film power resistor with its body and connection pads visible

Miba Unveils 55 W SMD Thick-Film Power Resistor in TO-263

20.11.2026
2
CapXon PM and EV surface-mount capacitors with cylindrical cans and rectangular mounting bases

CapXon Extends Polymer and SMD Aluminum Capacitors

20.11.2026
3
Vishay VJ series surface-mount ceramic safety capacitors with rectangular bodies and metal end terminations

Vishay Introduces X1 Safety MLCCs for AC Line Filtering

20.11.2026
1
Vishay 259 PHM-SI cylindrical aluminum electrolytic capacitors with blue insulating sleeves and snap-in terminals

Vishay Adds 550 V and 600 V Snap-In Capacitors

18.11.2026
24
illustrative image of film capacitors close to a circuit board

2026 Capacitor Price Shock: Where Film Capacitors Fit

17.11.2026
63
Exploded view of the Nisshinbo Silicon Motherboard: functional chip, silicon substrate, insulating layer, printed wiring, external passive parts and frame

Nisshinbo Silicon Motherboard Integrates ICs and Passives

17.11.2026
29
Murata MGJ2T2 SIP isolated DC-DC converter for SiC gate-drive power

Murata Unveils Isolated DC-DC for SiC Gate Drives

17.11.2026
28
Simplified buck, boost, flyback and isolated buck power-stage schematics showing switches, inductors, coupled magnetics, diodes and output capacitors.

SMPS Topology Selection: From Buck and Boost to Flyback and LLC

16.11.2026
48
Littelfuse AK-FB and AK-A high-power TVS diodes in axial-leaded packages

Littelfuse Introduces TVS Diodes for HVDC Protection

16.11.2026
25

Upcoming Events

Nov 24
16:00 - 17:00 CET

Select the Correct Components for Your DC/DC Converter

Dec 1
16:00 - 17:00 CET

Developing low-noise mixed-signal systems

Dec 8
16:00 - 17:00 CET

WE-CCMF: Design Principles, Layout Guidelines and Measurement Results for High-Speed EMI Filtering

View Calendar

Popular Posts

  • Buck Converter Design and Calculation

    0 shares
    Share 0 Tweet 0
  • Boost Converter Design and Calculation

    0 shares
    Share 0 Tweet 0
  • September 2026 Interconnect, Passives and Electromechanical Components Market Insights

    0 shares
    Share 0 Tweet 0
  • Capacitor Charging and Discharging

    0 shares
    Share 0 Tweet 0
  • RF Connector Types: How To Choose the Right One

    0 shares
    Share 0 Tweet 0
  • Passive Low Pass Filters: Fundamentals and EMI Design

    0 shares
    Share 0 Tweet 0
  • LLC Resonant Converter Design and Calculation

    0 shares
    Share 0 Tweet 0
  • Flyback Converter Design and Calculation

    0 shares
    Share 0 Tweet 0
  • Capacitor Symbols

    0 shares
    Share 0 Tweet 0
  • Capacitance and its Calculation

    0 shares
    Share 0 Tweet 0

Newsletter Subscription

 

Passive Components Blog

© 2015–2026
All rights reserved

  • Home
  • Privacy Policy
  • EPCI Membership & Advertisement
  • About

No Result
View All Result
  • Home
  • Knowledge Blog
  • Dossiers
  • PCNS

© 2015–2026
All rights reserved